How to read a dial indicator

Step by step with pictures: the parts, how to set it up, then how to read the turn counter and the big needle. Each step shows the indicator with the part you are reading marked.

How to read a dial indicator, step by step

1 Know the parts

Bezel: turn it to set zeroBig needle: 0.001" a markTurn counter: 0.100" a markStemPlungerContact point
The parts of a dial indicator. Each mark on the big dial is 0.001"; each number on the turn counter is 0.100".

The contact point on the end of the plunger touches the part. As the plunger moves, the big needle turns: each mark is 0.001". The small turn counter counts full turns of the big needle, each 0.100". Turn the bezel to put 0 under the needle.

2 Set it up and find runout

Stand holds it stillContact point touches the partTurn the part and watch the needle
The indicator is held still on a stand with the contact point on the part.
  1. Mount the indicator firmly with the plunger square to the surface.
  2. Push the plunger in about a quarter turn (preload) so it can read both ways.
  3. Turn the bezel to put 0 under the needle.
  4. Turn or move the part and watch the needle. The runout (TIR) is the highest reading minus the lowest: from 3 below zero to 4 above is 0.007".

3 Read the turn counter

0102030405060708090.001 in.100 per turn0123456789Counter past 3 = 0.300"
The small needle has passed 3: 3 full turns = 0.300".

Each number on the small dial is one full turn of the big needle, 0.100".

4 Read the big needle

0102030405060708090.001 in.100 per turn0123456789Big needle 47 = 0.047"
The big needle points at 47: 0.047".

Each mark on the big dial is 0.001", and it is numbered every 10.

5 Add them up

0102030405060708090.001 in.100 per turn0123456789Counter past 3 = 0.300"Big needle 47 = 0.047"0.300 + 0.047 = 0.347"
0.300 + 0.047 = 0.347".

Turns plus needle: the plunger has moved 0.347".

6 Metric indicators

01020304050607080900.01 mm1 mm per turn0123456789Counter past 4 = 4.00 mmBig needle 25 = 0.25 mm4.00 + 0.25 = 4.25 mm
Metric: counter past 4 (4.00 mm) and needle at 25 (0.25 mm): 4.25 mm.

A common metric indicator reads 0.01 mm a mark and 1 mm a turn, so the counter counts millimetres. Read it exactly the same way.

Try it yourself

Move the plunger with the slider and watch the big needle and the small turn counter. Switch to metric to see a 0.01 mm indicator.

What a dial indicator measures

A dial indicator measures how far its plunger moves, not the size of a part. It is used to check runout on a shaft, flatness, the position of a part in a vise, or how much a surface rises and falls. Most readings are a difference: where the needle ends up compared with where you set it to zero.

Balanced and continuous dials

A continuous dial reads 0 to 100 all the way around, like the ones above. A balanced dial reads 0 in the middle and counts up both ways (0 to 50 and back), which is handy for plus-or-minus readings around zero. Each mark is still worth the value printed on the face.

Practise reading a dial indicator

Practice this tool Print a free worksheet

Questions

How much is one revolution on a dial indicator?

On a typical 0.001" indicator, one revolution is 0.100". On a typical 0.01 mm indicator, one revolution is 1 mm.

What is the small dial on a dial indicator?

The turn counter. It counts full revolutions of the big needle.

What is TIR?

Total indicator reading: the difference between the highest and lowest readings as a part is turned or moved.

Sources

Measure Drill checks every number against these references or works it out from the exact definitions of the units.