How to read a vernier caliper
Step by step with pictures: the parts, how to measure, then how to read the main scale and find the vernier line that lines up. Each step shows the scales with the part you are reading marked.
How to read an inch vernier caliper, step by step
1 Know the parts
The beam carries the main scale. The sliding jaw moves along it: roll it with the thumb roller and hold it with the lock screw. The big outside jaws measure across a part, the small inside jaws measure holes and slots, and the depth rod comes out of the end to measure how deep something is. The vernier scale on the slide reads the thousandths.
2 Measure the outside of a part
- Wipe the jaws, close them and check the caliper reads zero.
- Open the jaws wider than the part, then close them gently and squarely on it. Use the part of the jaws near the beam, not the tips.
- Light, even pressure. Squeezing hard bends the jaws and reads small.
- Read it on the part, or lock it and lift it off.
3 Know the scales
The main scale counts inches (big numbers) and tenths of an inch (small numbers 1 to 9, each 0.100"). Each tenth is split into 4 small spaces of 0.025". The vernier scale on the slide has 25 lines, each worth 0.001".
4 Read the main scale up to the vernier zero
Look at where the 0 of the vernier sits. Read everything it has passed: inches, then tenths, then small spaces. Here: 2.000 + 0.300 + 0.025 = 2.325".
5 Find the vernier line that lines up
Run your eye along the vernier. Only one line lines up exactly with a line on the main scale. Its number is the thousandths. Tip: the lines on either side of it are off by the same small amount in opposite directions.
6 Add them up
Main scale plus vernier: 2.347".
How to read a metric vernier caliper
1 Read the whole millimetres
The main scale is in millimetres, numbered every centimetre (the 2 is 20 mm, the 3 is 30 mm). Read the last millimetre line the vernier zero has passed.
2 Find the vernier line that lines up
On a 0.1 mm vernier each line is 0.1 mm. Find the one line that lines up exactly with a main-scale line.
3 Add them up
Whole millimetres plus the vernier: 23.4 mm.
4 Finer verniers: 0.05 mm
A 0.05 mm vernier has 20 lines, with numbers that count tenths of a millimetre. A line halfway between two numbers adds 0.05 mm. A 0.02 mm vernier is read the same way with 0.02 mm per line.
Try it yourself
Slide the caliper and watch which vernier line lines up. The top shows the whole caliper; below it is a magnified view of the scales, like looking through a loupe.
How a vernier works
A vernier scale is a second scale whose lines are spaced a tiny bit closer than the main scale's. On an inch caliper, 25 vernier lines fit in the space of 24 main divisions, so each vernier line falls 0.001" shorter than the main line next to it. Only one vernier line can line up exactly with a main-scale line, and which one it is tells you the thousandths.
Other ways to measure
The same scales read inside, depth and step measurements. The caliper guide shows each one with a picture. For a step, put the end of the slide against the shoulder and the end of the beam on the lower surface.
Practise reading a vernier caliper
Questions
How do you read a vernier caliper in inches?
Read the main scale up to the vernier zero (inches, tenths and 0.025" divisions), then add the number of the vernier line that lines up exactly, in thousandths.
What is the least count of a vernier caliper?
The smallest step it can read: 0.001" on most inch verniers, and 0.1, 0.05 or 0.02 mm on metric ones.
Why do two vernier lines look lined up?
On a drawing or a worn tool, two neighbouring lines can look close. The true one is where the lines on both sides drift away evenly. If the 0 and last line both line up, the vernier adds nothing.
What is the difference between a vernier and a dial caliper?
A dial caliper replaces the vernier with a gear-driven dial that you read directly. A vernier has no moving parts to wear but takes more care to read.
Sources
Measure Drill checks every number against these references or works it out from the exact definitions of the units.